Cover
Vol. 19 No. 2 (2025)

Published: December 31, 2025

Pages: 84-98

Research Article

Enhancing the Mechanical Properties of EPS Mortar Using Waste Plastic Fibers   

Iba'a Jehad* 1 Abdulkader Al-Hadithi 2
1University of Anbar College of Engineering
2Civil Engineering Department, College of Engineering, University of Anbar, Anbar, Iraq
History
  • Received: July 13, 2025
  • Revised: October 15, 2025
  • Accepted: October 17, 2025
  • Available Online: December 31, 2026
DOI

https://doi.org/10.37650/ijce190207

Abstract

The aim of this research is to experimentally evaluate the mechanical characteristics of mortar mixtures containing expanded polystyrene (EPS) beads and reinforced with polyethylene terephthalate (PET) fibers. Fine aggregates were partially replaced with 10% and 20% replacement ratios of expanded polystyrene beads, as well as four PET fiber volume fractions set at 0%, 0.5%, 0.75%, and 1%. Standard specimens for compressive strength, density, split strength, and flexural strength were used to assess the mechanical properties of hardened samples, while the slump test was used to gauge the fresh-state workability. The findings showed that the weight of the mortar reduced when EPS beads were used in place of fine aggregates. However, incorporating EPS beads into the mortar led to notable decrease in its mechanical properties. The workability was negatively impacted by the addition of PET fibers. However, when 0.75% PET fibers were added, PET reinforcement significantly increased compressive strength by 32% and 27% in mixes with 10% and 20% EPS, respectively. Splitting tensile and flexural strength exhibited minor fluctuations, with overall improvements remaining within approximately ±10%. The density and ultrasonic pulse velocity reduce when adding PET fibers. At 20% EPS and 1% PET, the concrete's density dropped to approximately 2030 kg/m³.

Keywords

References

  1. Alobeadi, A. J., Al-Hadithi, A. I., & Aldosary, M. H. (2025). Structural Performance of Ferrocement Beams containing Plastic Waste Fibers and Longitudinal Holes Filled with Lightweight Concrete. Iraqi Journal of Civil Engineering, 19(1), 1-18.
  2. Al-Alusi, M. R. M., Kurdi, N. H., Al-Hadithi, A. I., & Hammad, A. (2024). An experimental investigation of the mechanical characteristics and drying shrinkage of a single-size expanded polystyrene lightweight concrete reinforced with waste plastic fibres. Construction and Building Materials, 415, 135048.
  3. Al‐Hadithi, A. I., Hilal, N. N., Al‐Gburi, M., & Midher, A. H. (2023). Structural behavior of reinforced lightweight self‐compacting concrete beams using expanded polystyrene as coarse aggregate and containing polyethylene terephthalate fibers. Structural Concrete, 24(5), 5808-5826.
  4. Salahaldeen, A. S., & Al-Hadithi, A. I. (2022). The effect of adding expanded polystyrene beads (EPS) on the hardened properties of concrete. Engineering, Technology & Applied Science Research, 12(6), 9692-9696.
  5. Ali, F. A. A. R., Al-Hadithi, A. I., & Al-Asafi, J. A. (2024, February). Enhancement the mechanical properties of ferrocement mortar by adding waste plastic fibers. In AIP Conference Proceedings (Vol. 3009, No. 1, p. 030045). AIP Publishing LLC.
  6. Araghi, H. J., Nikbin, I. M., Reskati, S. R., Rahmani, E., & Allahyari, H. (2015). An experimental investigation on the erosion resistance of concrete containing various PET particles percentages against sulfuric acid attack. Construction and Building Materials, 77, 461-471.
  7. Babu, D. S., Babu, K. G., & Wee, T. H. (2005). Properties of lightweight expanded polystyrene aggregate concretes containing fly ash. Cement and concrete research, 35(6), 1218-1223.
  8. Belloa, I. e. (2021). Assessment of Expanded Polystyrene Beads Waste as Partial Replacement of Coarse Aggregate in Lightweight Concrete.
  9. Gyawali, T. (2023). Effect of the mixing procedure on the properties of lightweight EPS mortar. Journal of Building Engineering. 68: p. 106012.
  10. Iraqi Specification IQS No. 45, (. Z. (n.d.). Iraqi Specification IQS No. 45, (1984), Zone (2).
  11. Iraqi Standard No. 5, 1. f. (1987). Iraqi Standard No. 5, “Iraqi specifications No. (5) at 1987 for Portland cement,” Icosqc. pp. 1–8, 1984.
  12. Al-Hadithi, A. I., & Abbas, M. A. (2018). The effects of adding waste plastic fibers on the mechanical properties and shear strength of reinforced concrete beams. Iraqi Journal of Civil Engineering, 12(1), 110-124.
  13. Khalaf, K. J., & Khalil, W. I. (2015). Studying the utilization of polymeric wastes to produce sustainable concrete (Doctoral dissertation, Doctoral dissertation, MSc. Thesis, Building & Construction Dept., Univ. of Technology, Iraq).
  14. Liu, N., & Chen, B. (2014). Experimental study of the influence of EPS particle size on the mechanical properties of EPS lightweight concrete. Construction and Building Materials, 68, 227-232.
  15. Mahmoud, Z., Al-Hadithi, A., & Aldosary, M. (2023). The effect of waste polyethylene terephthalate fibers on the properties of self-compacting concrete using Iraqi local materials. Iraqi Journal of Civil Engineering, 17(2), 19-33.
  16. Nasreldin. (2015). Nasreldin, M. xpanded polystyrene from the ground up. https://www.slideshare.net/kuwaitinsulation/mohamed-nasreldin-expanded-polystyrene-from-the-ground-up.
  17. Ochi, T., Okubo, S., & Fukui, K. (2007). Development of recycled PET fiber and its application as concrete-reinforcing fiber. Cement and Concrete Composites, 29(6), 448-455.
  18. Sadrmomtazi, A., Sobhani, J., Mirgozar, M. A., & Najimi, M. (2012). Properties of multi-strength grade EPS concrete containing silica fume and rice husk ash. Construction and Building Materials, 35, 211-219.
  19. Sharma, R., & Bansal, P. P. (2016). Use of different forms of waste plastic in concrete–a review. Journal of cleaner production, 112, 473-482.
  20. Xu, Y., Jiang, L., Xu, J., Chu, H., & Li, Y. (2015). Prediction of compressive strength and elastic modulus of expanded polystyrene lightweight concrete. Magazine of Concrete Research, 67(17), 954-962.