Composite beams, made up of a concrete slab and steel in the IPE steel section, are commonly used in bridges and buildings. Their main function is to enhance structural efficiency by merging the compressive strength of concrete with the tensile resistance of steel, thereby improving overall stiffness, ductility, and load-bearing capacity. This study offers an extensive review of the flexural behavior of steel-concrete composite beams, focusing on the interplay of concrete strength, shear connector types, and interaction levels in determining structural performance. It integrates experimental and numerical research to analyze critical parameters, including load-deflection behavior, shear transfer efficiency, and crack propagation at the steel-concrete interface. The study emphasizes the effect of concrete compressive strength, particularly in ultra-high-performance concrete (UHPC) and lightweight concrete, on stiffness, ductility, and load-bearing capacity while reducing self-weight and enhancing sustainability. The study revealed that fully bonded shear connectors, using CFRP sheets and welded plates, enhance flexural capacity and stiffness. In contrast, partial bonding or pre-debonding reduces performance due to crack propagation. Indented and hot-rolled U-section connectors enhance interaction and minimize slip, while uniform distribution of shear connectors optimizes load capacity and stiffness. Lightweight concrete decreases slab weight without compromising performance, and high-performance materials such as ECC, SFRC, and UHPFRC improve strength and ductility. Numerical modeling, particularly finite element methods, and higher-order beam theories validate experimental results, providing accurate tools for predicting structural behavior under various loading and environmental conditions.
Because of rising the need for health clinics in recent years, as well as the current economic climate, the researcher used value engineering to reduce costs while retaining the necessity of these initiatives. The aim of this study is to increase the value of health clinics through applying value engineering approach to the main building (two and a half floors). Collected data, function analysis, brainstorming and alternatives, evaluating and selection, and generating the value report are the steps followed. According to the study, using the value engineering process resulted in a cost savings of 32.15 percent, or (258.305.000) million Iraqi dinars without jeopardizing the desired outcome.
One of the most significant aspects of developing any region is establishing a viable road network and determining the relationship between landscape use and road networks. Adequate connectivity and direction are essential for the proper construction of any network. However, the Al-Ramadi road network has received far less attention and appraisal. As a result, the purpose of this study was to evaluate the current road network link in Al-Ramadi city. In addition, the GIS application was used in this study to show the city's primary features. The Alpha index, Beta index, Gamma index, and Eta index were utilized to evaluate the road network in this research. The primary goal of this research is to evaluate how successful the road network is in containing current road traffic and to make recommendations for the future traffic management efficiency to accommodate increase. The findings show that immediate upgrades, such as the construction of new roadways, are essential.
The reduction of gases emissions as one of its most significant long-term strategies in any country in the world. Many Iraqi cities suffered from the uncontrolled increasing in the number of vehicles which has a positive relationship with the emission of gases especially the carbon monoxide. This study aims to evaluate the effect of traffic characteristics such as logarithm of average flow, the percentage of heavy vehicles, and free flow speed on the emission of carbon monoxide. The study selected the main roads in Al- Ramadi network, the data was collected for traffic characteristics and carbon monoxide between 2018 to 2020. A random parameters approach was used to develop a model to estimate the carbon monoxide emission for 345 roadway segments, this approach was used due to the ability of this method to account the heterogeneity that raised from the traffic characteristics which led to predict more accurate results than other approaches. The results of the random parameters model show that the carbon monoxide emission increased due to increase of logarithm of average flow, the percentage of heavy vehicles, and free flow speed. The model results show that the parameters of logarithm of average flow, the percentage of heavy vehicles, and free flow speed was varied a cross the roadway segments.
Several different deterministic and probabilistic mathematical approaches have been used to develop modal split models. The data collected by a questionnaire survey approach is frequently associated with subjectivity, imprecision, and ambiguity. additionally, several linguistic terms are used to express some of the transportation planning variables. This can be solved by modeling mode choosing behavior with artificial intelligence techniques such as fuzzy logic. In this research, Ramadi city in Iraq has been selected as a study area. For the purpose of obtaining data, the study area was divided into traffic analysis zones (TAZ). The total number of traffic zones was set as 28 traffic zones, 22 were internal traffic zones and 6 external traffic zones. Field surveys and questionnaires are used to collect data on traffic, land use, and socioeconomic characteristics factors (age, gender, vehicle ownership, family income, trip purpose, trip origin and destination, trip time, waiting duration, duration inside mode, trip origin and destination, trip cost, and type of mode used for transport). The results showed that the modal split models based on the fuzzy inference system can deal with linguistic variables as well as address uncertainty and subjectivity and they gave very good prediction accuracy for future prediction. Fuzzy inference system proved that all factors affected the mode choice with a very strong correlation coefficient (R) equal to 93.1 for general trips but when the results were compared with multiple linear regression model found that the correlation coefficient (R) equal to 28.9 for general trips and the most influential factors on the mode choice are car ownership, age and trip cost. Thus, it can be concluded that fuzzy logic models were more capable of capturing and integrating human knowledge in mode selection behavior. In addition, this study will help decision-makers to plan transportation policies for Ramadi city
Ferrocement is a type of concrete made of mortar with different wire meshes. It has wide and varied applications in addition to its strength and durability. This research aims to combine ferrocement and sustainability, as over time, the consumption of plastics, especially plastic bottles, has increased and has serious negative effects if buried, burned, or chemically analyzed. Therefore, this research aims to benefit from this plastic waste and introduce it into the construction field by using plastic waste fibers in the concrete mixture instead of cement at a rate of 0.5% and 1% by volume. This research studied the mechanical properties of nine samples of ferrocement beams with dimensions of 1200 × 200 × 150 mm3. A longitudinal hole with a diameter of 50 mm was drilled in different places of the beams and filled with lightweight concrete to facilitate the use of the hole in service passes when drilled, with a study of the initial cracking loads and the resulting deflection in addition to the failure modes and the deflection resulting from the maximum load. The results showed an improvement in load resistance with an improvement in deflection at the maximum load, In addition to an increase in the improvement of Toughness and Stiffness of ferrocement beams.
The finite element method capable of simulating the behavior of deep foundations subjected to negative skin friction in Basrah soil is investigated. Single piles under drag forces are analyzed using the PLAXIS program with an axisymmetric model. Linear elastic, Soft Soil and Mohr-Coulomb constitutive relations are adopted, where higher order triangular element is chosen for pile and soil clusters. Both pile and soil are modeled using (15)-node triangular elements. Three sites in Basrah province (Umm Qasr Port, Khor Al-Zubair, and Shatt AlArab Hotel) were selected to perform this study. The soil profile and layer characteristics are obtained from the soil investigation reports. Where the negative skin friction is evaluated due to filling loads. It is Conclusion thatSmall relative displacements are necessary to activate the negative skin friction. The elastic shorting for pile effect negative skin friction, due to increase relative displacement. The elastic shorting of the driven pile is more than that of the bored pile due to the less cross-sectional area of the driven pile. The results revealed proportional relation between the developed drag forces and pile section dimensions, interface friction factor, and fill height, with a maximum effect on the section dimension and minimum effect on the interface factor. The locations of neutral points are not sensitive to the above-mentioned factors.
Polyethylene terephthalate (PET) fiber is a green-friendly fiber that is capable of enhancing the mechanical properties of wet-mixing shotcrete. The main purpose of this study is to see how varied volumes of waste plastic fibers (WPF) affect the flowability and mechanical properties of wet-mix shotcrete. For this aim, a variety of experimental tests based on WPF content were chosen. Fresh and mechanical tests included slump, T500, density, compressive strength, and splitting strength were applied. The results shown a improved in shotcrete performance as the WPF content increased. Among all fitting correlations, density and compressive strength revealed the strongest linear ship association. Due to greater interlocking between WPF and concrete matrix, WPF was a major use in enhancing splitting tensile strength. WPF had the most influence on splitting strength, with 23–31 percent, 7–23 percent, and 6–38 percent for 7, 14, and 28-day, respectively.
Since evapotranspiration typically makes up the largest portion of the terrestrial water cycle, it is one of the most crucial factors in determining how much water is available. This study evaluated four models (Penman-FAO-24(PF), Penman-Monteith -FAO-56(PM), Penman-Kimberly(PK), and Jensen-Haise (JH)) utilized frequently to calculate monthly reference crop evapotranspiration (ET_0) values for Ramadi irrigation project (fourth stage). The statistical indicators considered were the root mean square error (RMSE), Mean Absolute Error (MAE), Relative Error (RE), Correlation Coefficient (R^2) and mean bias error (MBE), models were used to estimate evapotranspiration, and by calculating evapotranspiration for Al-Ramadi city according to the climate data available to us, The (PF) model had the lowest MBE = 0.02945, greatest RMSE = 29.369, and highest R = 0.9641 values among the four models, demonstrating that it is the best. The JH model, which achieved the highest values of MBE = 0.00978 and RSME = 58.509, was the least accurate of the models.. The study's conclusions may be useful to farmers, decision-makers, and local water organizations in assessing irrigation water requirements, planning, and effective use of water resources.
The current research’s purpose is to examine how Ultra-High Performance Fiber Concrete (UHPFC) holds up in terms of strength and durability for strengthening purposes. For this reason, the experimental and the theoretical studies in this research attempted to assess different fresh and hardened properties of a variety of ultra-high performance combinations. Steel fibers were utilized to differentiate all of the program's combinations at percentages of 0.25 %, 0.5 %, 0.75 %, 1%, and 1.25 % by volume. Mini flow slump, compressive and flexural strength, ultrasonic pulse velocity, water absorption, and porosity tests were all used to examine the performance of the strength and durability of the material. The findings of this study's trials showed that steel fibers increased the strength of UHPFC. The steel fiber ratio of 1% gave the maximum compressive strength, whereas 1.25 percent yielded the highest flexural strength. Because the fibers function as a bridge, preventing internal breaking, the tensile test results were improved as the proportion of steel fiber rises. Through the use of the multi-objective optimization approach, the optimal ratio of fibers was chosen at the end of the laboratory work since it has the best durability and strength characteristics. Statistical software (Minitab 2018) was used to find the optimal combination of UHPFC that meets all of the requirements. The theoretical selected optimum ratio of 0.77% of fibers obtained from the optimization was evaluated and validated experimentally. The optimized mix provided 90.28 MPa, 14.6 MPa, and 20.2 MPa for compressive, splitting tensile and flexural tests respectively with better durability performance compared to other mixes prepared in this investigation.
The aim of this study is to investigate the effect of adding recycled materials such as CKD and RAP to weak cohesive soils, in addition to evaluate the change in the strength of these soils. This study was conducted on soil type MH, and only RAP particles finer than 10 mm were used in preparing the mixtures. 7, 14, and 28 days were selected as curing periods for soil- CKD and soil- CKD- RAP mixtures to obtain the effect of curing periods on soil improvement. The results showed that adding 20% of CKD to the natural soil increased the unconfined compression strength UCS from 0.43 MPa to 2.6 MPa at a 28-day curing period. Also, the results showed that adding 25% of RAP to the soil- 20% CKD mixture increased the UCS value to 5.3 MPa after 28 days of the curing period. The final results showed that the optimum contents of CKD and RAP added to the cohesive soil were 20% and 25%, respectively, while the optimum curing period was 28 days
This paper presents and discuses some properties of self-compacting concrete SCC containing optimum contents of different types of cement replacement materials CRMs like fly ah, silica fume and limestone powder. The purpose is to evaluate the performance of SCC mixtures to choose the best one for strengthening purposes of corroded reinforcement concrete beams. In a preliminary work, the theoretical optimum contents of the above materials were specified using statistical program (Minitab) and they were verified experimentally. This verification based on checking fresh properties such as slump flow, T500, L-box and segregation resistance as well as compressive strength. The optimum contents of CRMs: 14% fly ash, 19% limestone, 18% silica fume plus fly ash and 11% silica fume were selected and studied. Compressive, tensile, and flexural strengths were examined, as well as the modulus of elasticity, water absorption and porosity (which reflect the related durability properties) were examined. Test results show that the optimum verified theoretical percentage of a combination of fly ash and silica fume, at 18% by weight of cement with a fixed water-binder ratio of 0.33 showed the best overall performance. It was deduced that this SCC mix gave the highest mechanical properties and the lowest porosity and water absorption. For example, the compressive strength increased by 36.25% as compared to SCC mix containing limestone powder. Further, the porosity and water absorption decreased by 120.8% and 164% respectively as compared to the above same SCC mix. Thus, it could be used for strengthening purpose of corroded RC beams.
A study examined the ductility and toughness properties of beams made of reinforced concrete, including foamed, normal, and hybrid beams. Nine reinforced concrete beams were produced: three foamed concrete beams, three normal concrete beams, and three hybrid concrete beams. Each beam possessed identical rectangular cross-sectional dimensions of 1500 mm × 250 mm × 150 mm. The flexural parameters (ultimate load, ductility, deflection, and durability) were assessed for each type of concrete utilized. The study's results showed that the load-bearing capacity of hybrid concrete beams was comparable to that of normal concrete beams, whereas foamed concrete beams exhibited slight improvement in their ability to carry loads. The ductility of reinforced foamed concrete beams was lesser than that of normal concrete. For over-reinforced beams, the ductility of hybrid concrete beams showed a significant improvement of 61% compared to foamed beams and an even more significant increase of 91.7% compared to normal beams. Furthermore, the hybrid concrete beam with over-reinforcement had a flexural toughness of 18.7% greater than the normal concrete beam. Suggested that a hybrid section comprising conventional and foamed concrete be utilized to decrease ductility and improve stiffness.
Pavement rutting as a permanent deformation is a major type of distress in flexible pavements. In Iraq, the rutting in Expressway pavements represents a severe problem due to its widespread, and high severity and distress density levels. Therefore, driving is profoundly dangerous and causes severe damage to the vehicle’s parts and the life of its riders. To date, the number of comprehensive research on pavement rutting has been limited in Iraq, owing to several technical, logistic, and economic considerations. The current research studies the major mechanisms responsible for rutting and evaluates the structure of the Iraqi Expressway No.1 at selected sections. The work encompasses field and laboratory aspects. The field work involved; performing field surveys to investigate the pavement rutting condition and its extension with depth, characterizing pavement layers in terms of geometric material properties, and collecting field samples for lab tests. The laboratory work was detailed and included; performing a set of standard lab tests on samples taken from the asphalt, the subbase, and the subgrade layers as well as the natural ground. In addition, the project’s archive was searched for specific design information and limitations. In order to assess pavement rutting in the selected sections of Expressway No.1/R9 (A and B), two well-established evaluators were considered; The rutting severity levels and the distress density.
Slurry infiltrated fiber concrete (SIFCON) is a relatively new high performance material and can be considered a special type of fiber concrete (FRC) with high fiber content. The matrix consists of a flowing mortar or cement slurry that must penetrate well through the network of fibers placed in the mold. SIFCON has excellent mechanical properties combined with high ductility and toughness values. SIFCON a relatively new material, is composed of mud (cement or cement and sand), water, a plasticizer (water reducer), and fibers. All previous studies have used waste steel fibers, steel fibers and other fibers, but in this study, plastic fibers were made from polyethylene terephthalate (PET) by cutting carbonated beverage bottles. The main objectives of this study are: Determination the effect of the waste plastic fiber volume ratio on the strength and deformation of (SIFCON) samples under the influence of bending loads. Both flexural strength and toughness properties were determined by testing samples (100×100×400) mm at 28 and 56 days of age. The results obtained from these tests were compared with those performed on conventional tests. Aspect Ratio equal to (36.8) and three volume ratios (3%, 5% and 7%) of the total volume of the concrete mixture were used to add fibers with different volume ratios. A conventional concrete mix was created as a reference for comparison. Bending strength and fresh concrete tests were performed. And compared with the reference mixture and according to the analysis of the results. The results showed an improvement in bending strength .It was found through the flexural examination that the flexural strength of the mixture containing fiber percentage (7%) achieved the highest strength compared to the rest of the ratios used, compared with the reference mixture (Ref.) by (32.25, 27.5)% for ages (28, 56), respectively.
Composite columns are frequently used in constructing high-rise structures because they can minimize the size of the building's columns while increasing the floor plan's usable space. This study aims to create a nonlinear 3D finite element model for square composite columns designed for solid and hollow columns with various multi-skin tubes subjected to loads at eccentricities of (30 and 60) mm, compressive strength, and mesh size using the ABAQUS software. The comparison was based on the experimental data of six references of composite columns. While the compressive strength of concrete increases, the stiffness of the composite column rise. The ratio of concrete compressive strength values for composite column increased by (0, 12.3, 17.8, and 26.7 percent) for (fc'=25, 31.96, 35, and 40) MPa, respectively. The results of the different mesh sizes (20, 40, and 60) mm are showing; The experimental results and the finite element solution developed using the (20 X20) mm element correspond well. The nonlinear finite element analysis method was used, and the finite element outputs results were confirmed to be in favorable agreement with the experimental data
The frequency of accidents, as well as statistical models of accident frequency, are often used as a foundation for prioritizing improvements to roadway safety by several transportation organizations. However, the use of accident severities in safety programming has frequently been restricted to the locational assessment of accident fatalities, with little or no emphasis being placed on the full severity distribution of accidents (slight damage, serious damage) which is required in order to properly evaluate the advantages of several competing efforts aimed at improving safety. Within the scope of this research, we provide a sufficient modeling technique that may be used to get a better understanding of the accident severity level that occur on highway segments, as well as the influence of traffic characteristics such as annual daily flow, percentage of heavy vehicle and free flow speed. The modeling approach that used in this research (random parameters model) provides the possibility that the estimated values of the model parameters might differ from one road segment to another to account the heterogeneity of the independent variables. The estimated random parameters models are developed using accident severity data and traffic characteristics data that obtained from Fallujha – Al-Qaeam rural multilane road in Al-Anbar province, Iraq. The results of the estimated results suggest annual daily flow, percentage of heavy vehicle and free flow speed all have significant effect on the accident severity level. For the purpose of prioritizing highway safety improvements, a number of government transportation authority’s base their decisions on accident rates and statistical models of accident rates. The random parameters models have been shown to have significant potential for use as a sufficient method in the programming of highway safety.
This study was conducted to examine the impact of plastic fibers (WPFs) in an effort to improve some of the features of self-compacting concrete (SCC) using Iraqi raw materials. Waste polyethylene terephthalate fibers (waste PET fibers) from used beverage bottles were added. Some tests were carried out to determine the effects of adding WPFs on the fresh properties of new concrete, while additional tests examined the mechanical properties of hardened concrete. Because of this, self-compacting concrete blends were created with a constant water-to-binder ratio of 0.32 and a binder content of 525 kg/m3. The designated plastic fiber percentages contents were 0%, 0.5%, 0.75%, and 1% of mix volume. Self-compacting concrete mixtures' fresh characteristics were assessed for slump flow diameter, T50 slump flow concurrently, V-funnel flow concurrently, and L-box height ratio. The 28-day density, compressive strengths and flexural strength of self-compacting concretes were also measured. The use of plastic waste fibers had a slight effect on reducing the density of the produced concrete and a negative effect on the fresh properties. The compressive strengths were improved by using WPFs, with the maximum improvement equal to (11.065%) when compared to those made from the reference mix
Transport is a vital part of urban life and a foundation for society's growth. It is a wonderful indication of the growth and development of cities. It protects the free flow of people, commodities and the economy. . Despite the great advancement in technology, it still has many difficulties in developed and developing nations, particularly in our country, such as environmental issues, where congestion leads to traffic pollution, noise and a rise in cars which is a problem in itself.. So transportation is an issue. And it became a subject of attention, requiring consideration of sustainability in the planning and development of transportation systems. Ramadi has been chosen as a model in this study because of its significant impact on sustainable development and the approach that thins our study. Using the data from the study area, which included 27 neighbourhoods, were analyzed by the SPSS statistical program , the results showed that the indicators of the environmental dimension had a direct and strong relationship. For Ramadi and other Iraqi cities, a sustainable development system may be developed based on based on the two indicators of pollution and green areas (0.794 and 0.776), on which a choice can be made about sustainable urban environmental transport.
This study presents an investigation of the mechanical properties of normal concrete reinforced with discarded steel fibers (DSFs) resulting from tire manufacturing. DSFs were added to concrete in two different volume fractions of (0.25 %, and 0.5 %), and these fibers have dimensions of (40 mm length×0.92 mm diameter). The results showed that the compressive strength of the concrete was enhanced by (8.8%, and 3.3%) by adding of DSFs. However, the workability of concrete decreased at all added ratios. While the density is slightly changed. Also, the results indicate that the modulus of elasticity shows slight increases by (3.06%, and 2.25%). Additionally, the incorporation of DSFs improves the splitting tensile strength and modulus of rupture significantly. For concrete mixes having volume fractions of 0.25% and 0.5%, the splitting tensile increased by (7.89%, and 23.68%), and the modulus of rupture increased by (6.67% and 25.58%), respectively. It was concluded that using this type of discarded fibers can improve the mechanical properties of concrete as an alternative type for other types of industrial fibers.
SIFCON is a relatively new material and consists of slurry (cement or cement and sand), water, super plasticizers (water reducers) and fibers. In all previous research, steel fibers and other types of fibers were used, but in this study, waste plastic fibers Polyethylene Terephthalate (PET) created by cutting carbonated beverage bottles were used for the first time in the production of SIFCON. Three volume ratios (3%, 6% and 10%) of the total volume of the concrete mixture were used to add fibers in different volume ratios, and a reference concrete mixture was created for comparison. Tests of compressive strength, impact resistance, ultrasound transmission velocity check and other tests were performed on the constructed models. Compared with the reference concrete, according to the analysis of the results. The results showed an improvement in the compressive strength it increased by (18.5%), an increase in the impact resistance by (416.67%), and a decrease in the velocity of ultrasound by (19.42%).
ABSTRACTStudies in geotechnical engineering have the nonlinear behavior of soils. An experimental study was carried out on models of piled rafts, and four piles with a diameter of 25 mm and a length of (300, 400, and 500) mm were taken, with a raft of (180x180) mm, and compared with the piled-raft system of 180 × 180 raft and nine piles of 19 mm and 500 mm in diameter and length respectively. They were tested for raft resistance, number of piles, length, and diameter while maintaining the spacing between piles. Test results showed the raft performance improved by 76% when adding piles. The increase in the (L/D) ratio for variable (L) length leads to an increase in pile share of 87% for the groups (2×2). Also, pile share was increased by 10% with a decrease in the diameter of piles and an increase in the number of piles in the group. Therefore, the increment in each pile’s skin friction results in an increase in the bearing capacity of each pile.
Recycling the old paving waste and reusing it in the construction of new highways was resorted to, and this is a good step from an economic point of view, as well as from an environmental and health point of view, as it reduces carbon emissions and eliminates a large amount of disposable reclaimed asphalt pavement materials (RAP). This study aims to evaluate the best layer of pavement structure; base, binder, and surface layers for inclusion (RAP) materials based on stability and indirect tensile strength. In addition, highlight the best percentage that can be added from RAP to achieve positive results and better than that associated reference mixture in terms of Marshall test and Indirect tensile strength test RAP materials collected from different sources Karbala and Fallujah, were adopted in this study at percentages of 20%, 30%, and 40% by weight of the asphalt mixture. Two scenarios of incorporating RAP materials have been adopted : The first is considered that RAP as a black rock in which the effect of aged binder surrounding the aggregate of RAP is neglected while the second is not considered RAP as black rock and the influence of aged binder in RAP materials has been taken into consideration. Dora bitumen has been adopted in the current study which is used commonly in Iraq. It has been highlighted that the best layer in which RAP can be incorporated is the base layer, with a percentage up to 40% that RAP without considering RAP black rocks regardless of the sources of RAP
Wind and water levels influence wave overtopping and consequent coastal flood threat, which is especially important in hyper-tidal bays where even modest variations in wave heights may be devastating if they coincide with high tides. The influence of wind and wave characteristics on wave propagation, as well as the sensitivity of significant wave height, are numerically investigated along the Gaza Strip's beachfront as an example. Wind waves with a high amplitude and short duration are susceptible to opposing winds, and their steepening effect varies throughout the bay shoreline, underlining the impact of shoreline geometry and bathymetry on wave hazard. The findings contribute to our existing knowledge of the complex interplay between wind and waves, as well as the crucial variables that maximize danger and hazard variability along the coastline. The findings of this study can assist port and harbor managers prevent financial losses due to downtime, influence sustainable coastal sea defense design, and better understand how wave danger may change in the future owing to shifting storm tracks. The findings can also be used to improve coastal infrastructure design and disaster response planning. Two scenarios were investigated with a wind direction of 330 and 30. It seems that when the wind direction is 330, it produces a higher Hs of 1.2 m and relatively larger wave return period with a range of 12-22 s and a higher wave energy dissipation of 220 N/Ms. In contrast, when the wind direction is 30, it produces a smaller HS of 1m with a short wave return period of 15-17s and smaller wave energy dissipation of 120 N/Ms. Overall, a wind direction of 30 has fewer occurring chances over the year but it seems to produce a destructive wave that are spread over the whole coast with a rapid return period.
The present research aims at the comparison of the production time between the manual and computerized surveying systems. The surveying system consists of data acquisition, processing and plotting the engineering plan and contouring .The current computerised system is designed and tested using the pulse Total Station instrument GPT-2006, P.C. computer, traverse network adjustment computer programs, Auto Cad 2005, 2010 and Surfer- 9 contouring program. The results of the current field experiments showed that the computerized surveying system offers a considerable savings in the data acquisition, processing and plotting times as compared with the manual surveying system, i.e. for traversing , the reduction in the production time is up to (84%), for plan ( up to 74%) and for contouring ( up to 84%). The practical applications of the current research are in the fields of civil engineering projects ( roads, buildings, etc.), irrigation and environmental engineering schemes.
The problem of discarded tires has received a lot of attention from many authors. Incorporation of rubber aggregate recycled from waste tires is one of the solutions to this issue. This research is based on evaluating fresh and hardened properties such as slump flow, T500, segregation resistance, and L-box tests, compressive strength, impact resistance, and flexural toughness. Rubber aggregate replacements in the self-compact concrete mixes was 10% by volume of fine aggregate. Additionally, both PET and steel fibers are utilized at a volume rate of 0.25%.The outcomes indicate that introducing rubber declines rheological and hardened properties, whereas incorporating hybrid fibers enhances hardened properties such as compressive strength, impact energy, and flexural toughness. The best increase impact energy was obtained at roughly 166.6% when 0.25% hybrid fibers and 10% rubber were used. 74.21 was the greatest increase in flexural toughness when 0.25% hybrid fibers (SCCH3) were used. As for the compressive strength, it was the highest by about 11%.
Sustainable buildings reflect the interest rising of Urbanism sectors in issues of economic development, optimal utilization of natural resources and greater reliance on "renewable" sources of energy. The objective of the research is to identify and Diagnosis the priority of alternatives to sustainable projects with the of relative importance and to review the value engineering indicators in building and the possibility of applying sustainable building standards such as British Standards (BREEAM), US Standards (LEED), Pearl Rating System and Green Pyramid Assessment System. The research is based on four axes. The first axis is the foundations of architectural design to serve the optimum use of the available resources. The second axis is based on the methods of producing building materials with optimum use of natural resources; Third axis: The sustainable use of the building to achieve conservation of the environment using economical sources of energy, waste recycling and maintenance of the building according to the required specifications. The fourth axis, which means Using renewable energies to provide the building with the energy it needs. The literature and researches in the field of research work were reviewed, which included the concept of applying value engineering method in the sustainable buildings and the most important areas of their applications during the stages of completion of the project and what are the basic considerations that should be provided in the construction projects, Which represents the practical aspect in relation to the various stages of the field study, which includes aspects related to the field survey, through the preparation and Configure of questionnaires derived from the theoretical study and interviews and also focused on the indicators and areas of applications during the stages of the project (pre-construction stage, implementation stage, A maintenance and operation, post-construction phase (end of the age of the building) and what are the basic considerations that must be provided in the construction projects. The research provided this results: The Sustainable Buildings Projects location Selection Index is The most important indicators of value engineering for sustainable buildings where relative importance of it is 72%, according to the respondents' answers, conversely the architectural index, with its relative importance of 55%, while the electromechanical index was 68% and the constructional index by 65%. And the development of a waste management program during the process of construction and operation so that this program achieves the minimum recycling and the use of new alternatives to building materials drawing on what has been developed within other areas in the development of the construction industry.
Concrete is produced from millions of tons of Cement, which emits a significant amount of carbon dioxide from cement mills and contributes to global warming. Therefore, it is important to seek out less expensive and more environmentally friendly substitutes for OPC. While various substitutes are available, such as recycled glass, marble, silica fume fly ash, or agricultural waste like rice husks or wheat straw, the performance of concrete is significantly affected when bentonite is used as a replacement for Cement. This study aims to evaluate Jhelum bentonite, which is located at 32°56′ north and 73°44′ east longitude, as a replacement for Cement in different ratios (0:100, 10:90, 20:80, 30:70, and 40:60) to improve the durability of the system as more bentonite is used to replace conventional Portland cement, the workability, density, and water absorption of the new concrete all decrease. Compressive Strength, Tensile Strength, and flexural Strength of blocks and cylinders were tested after being cured for 7 and 28 days. Analysis of these strength tests revealed that the mixes containing bentonite were weaker after 7 days compared to 28 days, and the Strength of blocks was reasonable compared to cylinders.Keywords: Bentonite, Concrete, Compressive Strength, Tensile Strength.
Organic soils are problematic soil for various engineering applications due to their high compressibility and low shear strength which need to be improved. For many soil improvement techniques, using waste materials, such as fly ash (FA), is a practical and sustainable process. In this research, FA and geopolymer were used e used to reduce organic soil's compressibility. A one-dimensional consolidation test was performed to evaluate the organic soil's consolidation and compressibility properties. The geopolymer was prepared using 20% FA and of sodium hydroxide ratio and sodium silicate alkali solutions. The geopolymer specimens were first cured for 2 hours at 45 and 65 oC, then cured for further 28 days at room temperature. The consolidation test results showed that FA-based geopolymer is effective in stabilizing organic soils due to the observed improvement in the compressibility, consolidation, and permeability characteristics. The compression index decreased by 98.16%, and the permeability decreased by 95%.
Collapse of gypseous soils may cause excessive settlement and serious damage to engineering structures. Various improvement approaches, such as mechanical techniques and chemical additions, have been used to reduce the collapsibility of these soils. The odometer test has traditionally been used to assess the collapsibility of the improved gypseous soils; however, because the small size of test specimens, this method may not adequately reflect field conditions. In this research, a laboratory model test of 600 x 600 x 600 mm with a model footing of 100 x 100 mm was developed to measure the collapse characteristics of a gypseous soil. The top layer underneath the footing was improved by compaction, cement kiln dust (CKD), geogrid, and a combination between CKD and geogrid. The top layer was improved at two values of thickness of 50 and 100 mm. The results obtained from this study indicate that the values collapsibility settlement reduction factor for compacted soil and the soil treated with CKD were 75 and 82%, 89% receptively. These values increased up to 95 % when a combination of CKD and geogrid was applied. As discussed herein, the aforementioned treatment methods can effectively be used to improve the collapsibility of gypseous soils.
Value Engineering is one technique to distributed the resources fairly and perfect progress with honest meaning to decrease the expenditure , perform functions to improve the value element in project through decreasing the cost and developing the quality as well as choosing the better alternative to get the best quality . The research studies the value engineering technique by a field surveying and questionair submitted to different project personal in ALanbar government trough many stages beginning primary and finial design to construction project stage and the last operating and maintenance stage. Many site visits and personal interviews were carried out with their actual onsite experience on some of construction projects. Many useful conclusions and recommendations, one of them the researcher recommended to use the value engineering in contracts which have been support the economic national and save money to finance other projects.
Increasing the bearing capacity of shallow foundations is a significant challenge in the urban environment due to increased population growth. This paper presents the bearing capacity of circular foundations encircled by a diaphragm wall. In this study, the effects of diaphragm wall depth (0.5 D, D, 2 D) (D is the foundation diameter) of the foundation on the bearing capacity of the foundation are investigated. Varying relative densities of sand soil (loose, medium, and dense) are utilized. The results of the experimental tests show that the diaphragm wall possesses an influence upon the settlement and the foundation bearing capacity. Where, the capacity of bearing increased as the diaphragm wall depth increased. On the other side, increasing the depth leads to a decrease in the settlement ratio of about 57%. The results of experimental work also demonstrated that the best depth is between D and 2D for all types of relative densities
Foamed concrete (FC) is a type of lightweight concrete characterized by a high void space ratio and cementitious binders. In this research, the fresh and mechanical properties of fiber-reinforced modified foamed concrete (made with fly ash, silica fume, and superplasticizer) with a density of 1300 kg/m³ were studied. Carbon fibers of different lengths (12 mm, 20 mm, and 28 mm) were introduced in two ways: as single fibers (12 mm) and as hybrid fibers combining lengths of 20 mm and 28 mm.
The results showed that the compressive and split tensile strengths increased by approximately 43% compared to the control mix (modified with additives) when using a single fiber of 12 mm at a volume proportion of 0.4%. In contrast, using hybrid fibers resulted in increases of about 65% and 66% in compressive and split tensile strengths, respectively. When compared to the single fiber method, the hybrid approach improved compressive and split tensile strengths by about 15% and 16%, respectively.
Scour around bridge piers is a well-known threat to bridge stability worldwide. It can cause losses in lives and the economy, especially during floods. Therefore, an artificial intelligence approach called artificial neural network (ANN) was used to predict the scour depth around bridge piers. The ANN model was trained with laboratory data, including pier width, flow velocity, particle diameter, sediment critical velocity, flow depth, and scour depth. The data was divided into 70% for training, 15 for validation, and 15% for testing. Besides, the ANN model was trained using various training algrthins and a single hidden layer with 20 neurons in the hidden layer. The results showed that the ANN model with Bayesian regularization backpropagation training algorithm provides a better predicted scour depth with a correlation coefficient (R) equal to 0. 9692 and 0.926 for training and test stages, respectively. Besides, it showed a low mean squared error (MSE), which was 0.0034 for training and 0.0066 for the test. These results were slightly better than the ANN with Levenberg-Marquardt backpropagation with R training equals 0.9552 (MSE training = 0.0047), and R test equals 0.838 (MSE test = 0.007).On the other hand, the ANN model with a scaled conjugate gradient backpropagation training algorithm showed worse predictions (R training = 0.7407 and R test = 0.6409). Besides, the ANN model shows better outcomes than the linear regression model. Finally, the sensitivity analysis has shown that the pier width is the most crucial parameter for estimating scour depth using the ANN model.
In this study, the structural behaviour of RC-deep beams of glass fibre-reinforced polymer (GFRP) rubberized concrete is investigated. Rubberized concrete is manufactured by replacing fine sand aggregate with rubber crumbs in volumetric replacement ratios. The main variables were the crumb rubber content (0%, 10%, and 20%) and the main reinforcement ratio. Tested Six samples of deep beams with different dimensions (b = 150, h = 300 mm, L= 1400 mm) were under a four-point load until failure. The parameters under investigation were the mechanical properties of mixtures, load-midspan deflection curves, toughness, and the load-strain relationship. The results indicate that the increased crumb rubber content led to a decrease in the mechanical properties of rubberized concrete mixtures. It was found that the behaviour of all samples of rubberized concrete affected the deflection load curve, the ultimate load, and the increase in deflection. The sample R2-10% Rub showed the highest toughness among the tested samples, with an increase of 301.6% compared to the reference.
In recent years, hospital waste has been one of the most serious issues in Iraq and other parts of the world. The current study aims to measure and analyze hospital waste output across all departments at the Ramadi Teaching Hospital. The data on waste generation rates gathered for the study were primarily based on existing records of field management of hospital waste over the course of eight months (one week per month) for all departments in the hospital; however, some random sampling information was provided to supplement the data. The results revealed that the estimated rate of medical waste creation at Ramadi hospital was between 144 and 188 kg/day, whereas the general (non-medical) waste generation was between (240-278) kg/day. In terms of patient numbers and per occupied bed, the average medical waste generation rates were from 0.60 to 0.90 kg/patient/day and (0.85-1.11) kg/bed/day, respectively, whereas the average general trash generation rates ranged from 0.86 to 1.15 kg/patient/day and 1.42-1.64 kg/bed/day. The recent analysis concluded that the hospital's segregation procedure is still inefficient, and there is room for improvement in terms of reducing hazardous medical waste creation
Considering the corporations of the projects engineering in the universities from important corporations because they which work from projects contribute in prosperity and development of construction. Although for the quality management importance and concept application on the effects of these corporations, therefore must be first application quality management in these projects. The aim of this research to study the management system which used in the engineering affairs corporation (University of Tikrit study case). The harmony evaluation purpose between the management systems with the quality management system dependency on the tests menus which limited I.S.O. 9001/2000 and visit the corporation of projects engineering in university of tikrit for study the management system. Where as a questionnaire form was prepared, included answer on the questions of the tests menus, questionnaire distributed on the group of corporation engineering staff and some engineers whose they worked past in this corporation to fill the answers on questionnaire. The questionnaire results show that this corporation suffer disadvantage very clear in the corporation system structure. After that the Researchers suggest the management system build which can be more active and with high response on requirements of quality managemen
The evaluation of undrained shear strength (Su) in fine-grained soils is crucial for geotechnical engineering applications. This study aims to assess Su in fine-grained soils through laboratory testing and data analysis by different equations Su Undrained shear strength from field and Based on SPT-N Values. The introduction provides an overview of the importance of Su in geotechnical engineering and highlights the complexity of estimating Su in fine-grained soils. The material and methods section describes the collection of soil samples from Fallujah, which predominantly consist of silty clay and clayey silt. Field investigations were conducted to obtain Su measurements using field vane shear tests. The section also provides details on the field-testing data, including borehole depth, SPT results, consistency, Su, Su from SPT NOVO, and soil description. The laboratory testing and data analysis section presents the results of laboratory shear testing conducted on the collected soil samples. The testing involved determining the undrained shear strength of the soils using appropriate testing apparatus and procedures. The data obtained from the laboratory testing are analyzed to identify trends in Su and soil consistency. Based on the analysis of the data and the results obtained from the laboratory testing, it can be concluded that there is a relatively weak correlation between the undrained shear strength (Su) and the Standard Penetration Test (SPT) N-value. The correlations proposed by Sowers (1979), Kulhawy and Mayne (1990), Reese, Touma, and O'Neill (1976), and Terzaghi and Peck (1967) all show modest R2 values, indicating limited correlation between Su and N-value
Brick as a construction material can be considered one of the most common materials used for a very long time to construct buildings in iraq. The historic building represents one of the most important figures representing the rich history of iraq, which is built with bricks. Due to the aging of this type of building, a necessary improvement and retrofit need to occur. The paper investigates the ability to use different kinds of materials such as cfrp and srg to enhance the brick columns' structural capacity. From the results and discussions, it can be concluded that these materials are suitable to be used for this purpose with some limitations due to brick capacity itself.
The Gaza Strip in general, and the Islamic University of Gaza (IUG) in particular, are plagued by a lack of parking places, a lack of management and efficient usage of parking spaces, and illegal vehicle parking. This resulted in lost time and effort, besides traffic congestion. The study's goal is to provide a plan for implementing a Smart Parking System, which manages the parking spots on the IUG campus. To accomplish this goal, the researchers have identified the parking problems that face drivers at IUG, and then they have studied the impact of implementing the Smart Parking System. Researchers have used questionnaires to collect the raw data as one of the important tools in the field of survey. The data were analyzed using the Statistical Package for the Social Sciences (SPSS), as a useful tool for statistical analysis. The first results was the number of parking spaces is 300, which is greater than the number of potential vehicles occupying the university parking spaces at peak hours. Therefore, the issue is not the number of parking places, but how they are used. The result of the questionnaire presents that a large majority of respondents agreed that the IUG campus suffers from a lack of parking spaces, especially in rush hour from 8-10 am. The results indicate that 65.7% of the respondents park their cars near their workplace/study at the campus parking spaces, and 72.6% of the respondents do not use parking spaces with modern technology before. While 92.6% of the respondents encourage parking with modern technologies. Smart Parking System has assisted to resolve the issue of locating a parking spot on the IUG campus, resulting in less traffic congestion and a better flow of traffic. The Smart Parking System can be applied to all of the IUG's parking spaces and in the Gaza strip cities in the future
The design of reinforced concrete structures has traditionally relied on empirical techniques based on experience or experimental research on actual structural members. Although this approach produces a high level of precision, it is usually exceedingly costly and time-consuming. This paper studied the convergence between theoretical analysis (ACI 318-19 Equations) and numerical analysis (FEM) of eleven one way reinforced concrete slab specimens casted by shotcrete contains three types of plastic fibers including waste plastic (PET), polypropylene (PP), and hybrid (PET+PP) fibers with three addition ratios (0.35%, 0.7%, and 1%) for each type. The results concluded that the numerical analysis (ANSYS FE model) showed a good agreement with the theoretical (ACI 318-19) of one-way slab in terms of ultimate load, with a variance, and standard deviation equal to 0.00076, and 0.027 respectively. Hence, ANSYS v15 software can be used for the analysis of reinforced concrete slabs casted by shotcrete contain waste plastic fibers and polypropylene fibers.
The present study, the effect of changes that developed in concrete structures with time is presented. Two way slab investigated experimentally by [1]was analyzed using finite element method by ANSYS commercial program. Many parameters studied such as length to thickness ratio, reinforcement ratio and ultimate load ratio. The slab with dimension (2360*2360*63) mm and reinforced with different types of materials such as steel bars ,GFRP and CFRP (fiber reinforced polymer) bars . The results show that the strain increase gradually with time after apply the load. It can see that the strain in steel model increase with ratio of 19.98% when the load increase from 75% to 90%,and decrease with ratio 50% when the load decrease from 75% to 50% .That is, the change by increasing the strain is less and slower than the change by decreasing the strain, since the strain when dropping the load is less than the strain when lifting the load, because the structure has not undergone and its stiffness is still high and it is trying to recover its original shape. It increases significantly at the beginning, and then the difference decreases or stabilizes approximately after 330 days.
Adding fibers to the shotcrete concrete mixes is very important to increase the load carrying capacity, toughness, and reducing crack propagations by bridging the cracks. On the other hand, this fiber has an effect on the fresh and hardened properties of shotcrete. In this study, fresh properties evaluated by using slump flow, , and segregation resistance tests. Hardened properties included testing of air voids, dry density, water absorption, ultrasonic pulse velocity (UPV), compressive strength, and flexural strength. This works including two types of fibers in three forms (waste plastic (PET)fibers only, polypropylene fibers (PP) only, and hybrid fiber (PET and PP)), each form added by three percentages (0.35%, 0.7%, and 1%) by volume.The results showed that the addition of 1% of all types of fiber has a negative impact on fresh properties. Especially in shotcrete containing waste plastic fiber. Also, all specimens containing fibers showed a decrease in the ultrasonic pulse velocity (UPV) and an increase in air voids and water absorption compared to the reference specimens. Also, the results clarify that the addition of waste plastic fiber to shotcrete led to a slight decrease in dry density. The highest increasing in compressive strength of shotcrete recorded by about 8.2% with using 0.35% PP fiber and highest decreasing was 20.9% with using 1% waste plastic fiber. the highest increasing in flexural strength was 62 with using 1% PP fibers.
This main aim of this study is evaluate wide range of fresh and hardened properties of sustainable self-compacting concrete containing various types of Cement Replacement Materials with optimum contents of Polyethylene Terephthalate PET waste plastic as fibers and fine aggregate replacement. This is to evaluate effect of the two forms of PET and to determine the best CRMs could be used with sustainable SCC. such as limestone, glass powder and fly ash with high replacement rate of 70% by weight of cement were used while fourth one (kaolin) was used with replacement rate of 20%. PET fibers were added to SCC with an aspect ratio of 24.4 and 0.7% volume fraction whereas fine aggregate partially replaced by 4% of waste plastic. Four reference mixtures contained FA, LP, GP and KA only, same four mixtures contained 0.7% PET fibers by volume, and the other same four mixtures contained 4% PET fine aggregate by volume. The obtained results all tested fresh properties, which include slump flow, T500, L-Box and segregation resistance were within the limits of the specification reported in EFNERC guidelines. Further, the forms PET have an adverse effect fresh properties of SCC. As for hardened properties (compressive strength, splitting tensile strength, flexural strength and impact strength). Further, this produced type of SCC showed an range of compressive strength (15.2-31.64 MPa) at 28 days. It can be from the current study the best CRMs to be used in SCC containing PET wastes was FA in terms of most tested properties.
One of the most important aspects of the developing any area is creating a viable road network and defining the relationship between landscape use and road networks. Proper communication and direction are essential to the proper construction of any network. In addition to providing chances for production and consumption, resource extraction, and social cohabitation, the road network also functions as a hub for these activities. As a consequence, this contributes to the development of cities and the improvement of the level of living. However, Ramadi's road network has not received much attention and evaluation. To identify Ramadi road network transportation indicators, the researchers used geospatial information systems. Connectivity was assessed using the alpha, beta, gamma, and eta indices to describe and analyse the network. The data was collected in the first quarter of 2024. The Alpha, the beta, the gamma, and the eta indexes show weak Al-Ramadi road network connections. Indexes are 0.197, 1.26, 0.43, and 0.82. The research indicates a loss in network connectivity in the study region, necessitating the prioritization of new the roads and a city plan to mitigate network shortages.
If the employer believes that changing the shape, quality, or quantity of the work or some part of it is appropriate, he has the authority to order the contractor to do so. These instructions would extend the time it takes to accomplish the task and, as a result, the project's completion time. In the majority of situations, the employer and the contractor couldn't agree on how to compute the extra time the contractor was provided as a result of change orders. The aim of this research is to find a mechanism to determine the additional time required to carry out these works, which will vary based on the type of work, the increase in quantity for any work within the contract, etc.. Modify the nature, quality or type of any work, change the levels, lines, position and dimensions of any part of the work, and perform any additional work necessary to finish the works. A field visit and survey will be conducted on the various bridge projects as part of the research to determine the types of change orders and the additional time required for each of them, in addition to the most important reasons for not using the relative change length and how each project differs from the other. Mathematical software can be enhanced to reliably calculate the additional time for each form of change order. Most of the works expected to appear in variation order are steel and concrete works, and asphalt cladding works, with a frequency of each of them (25 percent), followed by excavation works, which have a frequency of (16.66 percent) in bridge projects.
ABSTRACT This research models the relationship between traffic characteristics and lane position on a six-lane divided highway. Both macroscopic and microscopic models were developed to analyze speed-density, speed-flow, and flow-density relationships for each lane, using linear and nonlinear approaches. Additionally, microscopic models were created to investigate speed-spacing, speed-headway, and headway-spacing relationships. Data was gathered using video recordings and radar speed guns, and traditional methods were applied to calculate density and spacing distance, which are typically challenging to measure in the field. Microsoft Excel and SPSS ver.26 software were utilized for analysis. The coefficient of determination (R-square) and the chi-square test were employed to assess the goodness of fit for the models. The results indicated no significant differences between the predicted and observed data, demonstrating critical traffic characteristics and providing insights into vehicular and driver behavior. These models can be utilized to identify various parameters of traffic characteristics in future studies on the examined highway.
The accumulation of wastes, especially plastic and car tires, has become a major problem facing society today. Therefore, through this research, these wastes were recycled and used to improve some properties of concrete. Recycled crumb rubber from car tires was used instead of sand as a partial replacement of 10%. The substitution was done by two methods: random and equivalent size substitution. As well, 1%polyethylene terephthalate (PET) fiber was added by the volume of concrete to improve some properties of rubberized concrete. Compressive strength, ultrasonic pulse velocity test (UPV) were conducted in this study to investigate the efficiency of PET rubberized concrete, as well the impact resistance test was also conducted to investigated the ability of PET rubberized concrete in term of energy absorption. Slabs of size (50cm×50cm×5cm) were utilized for low velocity impact test. The results indicated there were a reduction in compressive strength and UPV results were observed in PET fiber rubberized concrete the reduction were (37.47% and 5.4%) respectively as compared with PETC mixture and the result of dynamic modulus of elasticity show the same pattern of UPV result , in contrast there was an improvement in the impact resistance when PET fiber and crumb rubber were used it increased by(117.63% and 52.9% ) for random and equivalent replacement respectively as compared with PETC.
In the present paper, a one-dimensional finite element model for the analysis of composite beams of partial interaction is constructed. This model was verified against some analytical results available in the literature and achieved very good agreement with the natural frequencies and the time histories it was compared to. Then it was utilised to analyse partial interaction composite beams under the effect of uniform step loads and provided important information about the expected dynamic amplification factors, which turned out to be particularly high, and the effects of the linear stiffness ratio of the interface and the boundary conditions of the lower layer of the beam. The results, in particular, showed that even for extreme cases the orders of magnitude of the slip and the corresponding uplift remain the same. This pointed out an important finding that the uplift in the researched context, at least, is not negligible as it is widely assumed in the literature.
This research includes producing compacted concrete by rolling method and the possibility for using in highway construction field with studying the influence of adding waste plastic fiber resulting from manual cutting for bottles used in the conservation gassy beverage on different characteristics of this type of concrete. For the purpose of selecting mix proportions appropriate for rolling compacted concrete (RCC). Approved design method for ACI-committee (5R-207 .1980) was selected for this research. Destroying plastic waste by volumetric rates ranging between (0.5%) to (2%) was approved. Reference mix was produced for comparison. Tests were conducted on the models produced from rolling compacted concrete like compressive strength, flexural strength and split tensile strength. The analysis of the results showed that the use of plastic waste fibers (1%) has led to improve the properties of each of the compressive strength and flexural strength and split tensile strength compared with reference concrete. Compressive strength in 28 days with fiber ratio (1%) is higher than (52.15%) from compressive strength in 28 days of reference concrete. It can be also observed that each of the flexural strength and split tensile strength increases by (17.86, 25.61)%, respectively, from flexural strength and split tensile strength for the reference mix
In recent years, a number of researchers have adopted the wet packing (WP) approach to design different types of concrete mixes. Particle grading is a key to the optimization of the wet compactness density; for that reason, all empty spaces that exist in between large-size particles need to be completely filled with particles of smaller size. Previously-conducted studies in this field have been focused on measuring the particle size distribution’s packing density (PD) of the of granular matrices is the purpose of investigating how to increase the PD of cementitious materials. Thus, literature lacks models capable of predicting the optimal PD value. The current study collected and analyzed 216 datasets in order to construct a model for accurate prediction of PD. The main datasets were organized into two categories: modeling datasets and validation datasets. To configure the model in the best way, a hybrid gravitational search algorithm-artificial neural network (GSA-ANN) was also developed in this study. The findings confirmed ANN as an effective alternative for measuring the ultimate PD of cementitious pastes. ANN provided high levels of accuracy, practicality, and effectiveness in the process of predicting the PD value. Based on the final results, the implementation of the hybrid GSA-ANN technique causes a significant decrease in the number of tests conducted on experimental samples, which results in not only saving time and money, but also reducing the CO2 emission volume.
Determining building materials and their types and determining their effect on concrete properties are consistent with the technical and design variables of buildings. From this point of view, the research came to include theoretical studies and empirical tests for some materials, focusing on the aggregate as a basic material involved in the formation of concrete. The first part includes the introduction, research problem, assumptions, importance, and purpose of the research. the second part was to conduct practical experiments by designing different concrete mixtures in the mixing ratios and the type of aggregate until results were reached regarding the resistance of the concrete that was produced as a result of the difference in densities between ordinary aggregate concrete and lightweight aggregate concrete. Through that, for example, the lightweight aggregate with an age of (7) days and a mixing ratio of (1: 2: 4) gave strength to the models used (19.58) Mpa, and for the same mixing ratio and at an age of (28) days, it gave durability ( 22.83) Mpa. When the mixing ratio was changed to (1: 1.5: 3), it was (25.74) MPa and (32.34) MPa at the age of (7) days and (28) days, respectively. These results give an accurate indication that the aggregate is light in weight with similarity to the ordinary aggregate in obtaining concrete with a bearing strength within the approved specifications without guaranteeing the environmental treatments and the resulting loads
Microbial-induced carbonate precipitation (MICP) is a fast-evolving technology for cementing sandy soils, improving ground, repairing concrete cracks, and remediating contaminated land. The current work thoroughly reviews various factors that can impact the effect of the MICP technology on geomaterials. These factors include the type and strain of the microbes, concentration of bacterial solution, cementation solution composition and concentration, environmental factors (temperature, pH level, and oxygen dissolved), and soil properties. It was found that the type and strain of bacteria, concentration of bacterial suspension, pH value, temperature, and the reaction solution properties are the most affecting factors in controlling the characteristics of the produced calcium carbonate, which in turn affects the degree of bonding between geomaterials particles. For an optimal implementation of the MICP in soils treatment, it appeared that for the most commonly used bacterial strains a temperature between 20 and 40 °C, a pH between 6.5 and 9.5, and a cementation solution concentration of 0.5 mol/L, are typically recommended.
Pavement maintenance and rehabilitation prioritization are conducted based on the accessibility of overall measures for evaluating the condition of each section in the pavement network. Regularly, the pavement condition of each section has been evaluated by some common condition indicators. One of the most important indicators is the present serviceability index (PSI) which is adapted to depict the functional performance regarding ride quality. The main aim of this study is to develop a prediction model of ride quality for flexible pavement using the fuzzy logic technique. The data of input variables are extracted from the database of Long-Term Pavement Performance (LTPP). The research involved 36 pavement sections with 319 data samples for pavement networks of different states in the USA. The ride quality measure which is PSI estimated by the AASHTO equation represents the output variable, whereas patching area, cracking length, slope variance, and rut depth are considered input variables. The results showed that the fuzzified model of ride quality prediction has a decent accuracy with a high determination coefficient. In addition, based on the testing results, the developed prediction model showed a strong accuracy to predict the ride quality index
ABSTRACTAn operational analysis is an analytic evaluation of operation on an existing freeway ramps. In this case, all traffic and roadway conditions must be specified. The output of operational analysis is an estimate of the level of service for the ramp in question and of the approximate speed and density at which the traffic stream operations.A ramp is length of roadway providing an exclusive connection between two highway facilities. On freeways, all entering and exiting maneuvers take place on ramps those are designed to facilitate smooth merging of on-ramp vehicles into the freeway traffic stream and smooth diverging of off-ramp vehicles from the freeway traffic stream onto the ramp.The aim of this paper is the operational analysis of ramps on existing 6-lane freeway. This analysis involves the consideration of known freeway of Mohammed Al-Kasim freeway in Baghdad city. Given known geometric roadway conditions and projected traffic conditions, the operational analysis yields an estimate of the level of service and of the speed and density of the traffic stream. This paper has described the procedure for determining the level of service on Mohammed Al-Kasim freeway ramp sections as presented in the Highway Capacity Manual (HCM, 2000). Levels of service are determined for all ramps of the freeway using )HCS2000( software. Level of service of all ramps are similar at AM and PM peak hour periods, because the data was collected under ordinary traffic conditions.
Thin plate bending analysis is an important research subject due to the extensive use of plates in the different fields of engineering and the need for accurate solutions. This article uses the Ritz variational method and a superposition of trigonometric and polynomial basis functions to solve the Kirchhoff-Love plate bending problems (KLPBPs). The unknown displacement function in the Ritz variational functional (RVF) to be minimized is sought as linear combinations of basis functions Fm(x) and Gn(y) that are found by superposing sine series and third degree polynomial functions with the polynomial parameters determined such that all boundary conditions of deformation and force are satisfied. The displacement is thus expressed in terms of unknown displacement parameters Amn which are found upon minimization of RVF with respect to Amn. The minimization process gave a matrix stiffness equation in Amn with the stiffness matrix and force matrix found from Fm(x) and Gn(y) and their derivatives. The algebraic equation is solved, and the deflection and bending moments obtained. The problems considered were clamped (CCCC) plates under uniform and hydrostatic distribution of loads and plates with opposite edges clamped, the rest simply supported (CSCS) under uniformly distributed loading. Comparison of the solutions by Generalized Integral transform method, Levy-Nadai series method, and symplectic eigenfunction superposition confirms that the present results are accurate.
The performance of the structural materials (concrete and steel reinforcement) and the behavior of the structural members after they were exposed to high temperatures have been considered the main topics of the current literature review. All varieties of concrete mixtures lost their compressive strength after 300˚C, even though there was no discernible strength loss between 150 and 300˚C. It was also discovered that the heating time had no appreciable impact on the strength loss when the exposed to heat less than 300 ˚C. Above 300 ˚C. Concrete begins to lose strength after being exposed for longer than one hour; the greatest loss of strength occurs during the first and second hours of exposure. Both the cured cement paste and the aggregates undergo chemical and physical changes at temperatures ranging from 600 °C to 900 °C. The 5% weighted rice husk ash (RHA) blended concrete still had an advantage in compressive strength, over the concrete when subjected to temperatures up to 700 C for two hours. Adding more recycled glass and ceramic particles to regular concrete increases its overall compressive and tensile strengths. Concrete becomes more durable and has fewer cracks when there is a higher replacement rate for ceramic and glass particles. The splitting tensile strength decreased with increasing temperature, changing from 60% to 70% of its initial strength after 600 °C. In this review, the better performance of concrete than the other concrete in terms of mechanical, physical, and durability properties at both room temperature and high temperature were concrete with 10% waste glass powder (WGP) substitution as a partial of cement and 10%–20% crushed glass (CG) substitution as a partial of aggregate .
To classification groundwater quality in the study area, three wells were drilled at a depth of 10m and selected two locations across Al Warrar Canal to represent their water quality. Water samples were collected from these wells and the Warrar Canal to examine water quality. Then results were compared against the World Health Organization (WHO) limits to study the Index of Water Quality (WQI). WQI was calculated according to the Canadian Council of Ministers of the Environment (CCME), and the quality of water was evaluated for domestic and irrigation uses. The samples were tested for electrical conductivity, pH, temperature, total dissolved solids, chloride, total hardness, nitrate, and alkalinity according to the standard methods. The results of laboratory analysis showed significant differences among the wells and Warrar Canal water quality in the measured parameters according to WHO limits. Due to many human activities like urbanization, agrarian overflow, drainage of untreated sewage, and industrialization, high values of trace elements and heavy metals were recorded in wells three. For agriculture purposes, the results show that the water in the three wells is very high salinity, where the Warrar Canal is high salinity, and Canal water causes saline and alkali damages. It was recommended that the WQI in three wells was poor water quality whereas, marginal water quality was pointed in AL Warrar Canal.
The goal of this study is to determine the impact of ground motion recordings (GMs) selection on the seismic performance evaluation of reinforced concrete (RC) structures. From three GMs in ASCE7-10 to eleven GMs in ASCE7-16, the ASCE7 has upgraded the minimum GMs utilized in seismic analysis, When the GMs are used to evaluate an existing structure, the earthquake load may under or overestimate the structure's capacity. The case study is an existing RC building, dual system, and unsymmetric in-plane and height. Because of these asymmetries, the Non-linear Time History Analysis (NTHA) is the most accurate method. It is performed for 30 GMs in directions X and Y. The GMs were chosen and scaled to meet the Basrah city response spectrum curve (RSC), which is based on the existing Iraqi seismic code. The study parameters that were investigated are included story implication ratio, torsional irregularity index, floor rotation angle, and plastic hinge formation. These parameters are investigated in three cases. The selection of GMs for Case 1 and 2 are based on the ASCE7-10 while Case 3 is based on ASCE7-16. The comparison between cases is shown a considerable difference in structural response could lead to various retrofitting decisions. The findings revealed that existing RC buildings constructed in accordance with ASCE7-10, particularly medium and high-rise structures, should be re-evaluated
Crack monitoring of pavements is an ever-evolving technology with new crack identification technologies being introduced frequently. Although older technologies consisted of physical removing the pavement section using coring, however new methods are available that are non-destructive and yield a higher performance than conventional technologies. This paper compiles various crack monitoring technologies such as wireless sensor networks, photo imaging, laser imaging, 3D road surface profile scans, acoustics wave propagation technology, embedded strain sensors and onboard vehicle sensors that majorly use an artificial intelligence algorithm to identify and categorize the cracks. The research also includes the use of convolutional neural network that can be used to analyze pavement images and such neural network can localize and classify the cracks for crack initiation and propagation stage. The research concludes with the favor of using the optical imaging technology called Syncrack which serves better performance in terms of time of prediction by 25% and accuracy by 30% when compared to other sensing technologies.
AbstractThe aim of this study is to analyze the slope stability for sections in Al-Furat River where engineering construction build on it, when a sudden decrease in the river water level happens. Two sections were chosen from the river in the area located about 35 km away from Ramadi city called Tel Aswad where undisturbed samples are taken and laboratory tests are done to obtain the soil parameters which are used in Geo-Slope program. The finite element method was applied in this study with elastic-plastic soil model. The analysis results show that the sections slope chosen from the river are stable. The second purpose of this analysis to reduce the risk of using earth structures when engineering construction build on it. Also, it is clear that the values of factor of safety calculated by the FEM are low compared with limit equilibrium methods.
An essential part of managing construction projects is productivity estimation. The accuracy of the construction productivity estimate determines the management quality. This research established a multi-variable linear regression and another mathematical model for the same variables to assess the productivity of building projects using the logistic regression approach. Data from residential, commercial, and educational projects in various regions of Anbar was utilized in the research. Numerous dependent variables were chosen with care. These independent factors, which include age, experience, the quantity of work, level of execution, and security circumstances, may be divided into objective and subjective variables. The person-hour/unit and the cost/unit are two inputs to the system that are used to measure input/output, the parameter known as productivity. The first is used for procedures that need a large amount of labour and is focused only on labour. All impacts are combined in the second cost/unit. The researcher came up with an equation that contains the following factors (Health condition, equipment available, Security, labor, Quality work, morale, the material available, site condition, Experience, Weather, Height, and Age ).
Traffic movement is considered a compound phenomenon that is impacted by behavioural, economic, and physical aspects. It is performed within the context of an urban system that consists of road networks and crossings, where the movement crouches to depend. The measuring of identifying their size and densities and current problems helps to Improve and development for roads and streets network existing and important is intersections for purposes the accessibility, potentiality of future intersections, and network development towards constructing a composition to raise the quality and the efficient performance of roads and streets. The study was dependent on a traffic survey for intersections, areas of urban intersections, and the road network of Al-Ramadi city, as well as the number of vehicles that generated a large volume of traffic flow. The use of the program (HCS 2010) to detect appropriate for purposes decreasing traffic congestion and delayed trip time in the areas based on existing and future districts that generate different types and purposes of journeys to lessen the delay trip time to lessen traffic congestion. Therefore, research looks at both sides: first, a study of the existing intersections of the main road network and urban streets, including an examination of the components and shapes of these intersections in the study area; second, an examination of the importance placed on these intersections by the planning and design process.
The structural behavior of steel plate girders with web opening is investigated in this study. An experimental and theoretical investigation of plate girders with different types of openings in the web was conducted. Two types of web opening is investigated (square & circular) opening. The experimental work included testing of seven plate girder specimens under two point loads. Three specimens were tested to observe the influence of the circular web opening. The influence of the presence of square web openings was studied by testing other three specimens. While the last one was tested without opening as a reference (control) specimen. These specimens had the same dimensions. From experimental results the ultimate load of girders decreases with increasing opening size, and the position of plastic hinge depends on the size of hole A nonlinear 3D finite element model was deveioped using FE program ANSYS to validate the experimental results Four- nodes shell element (SHELL 181) was used to represent the steel plate. The proposed finite element model was used to study the effect of web slenderness on shear resistance of plate girder with web opening. Equation was suggested to predict the shear resistance. The analysis study give good agreement with experimental work.
The gypseous soils are distributed in many locations in Iraq. The Engineering properties of such soil will be changed when it is wetted and it leads to failure which causes danger on the structures built on. This reason needs to study its properties and to find the way to treat it. In this study, natural properties of soil prepared from Samarra-Salah al deen governorate were studied. The gypsum content of soil is about 32%. To improve this soil, many trials were carried out on the soil by additive of Portland cement and calcium chloride. For the importance of the compressibility of the soil, the effect of the additives were studied and it is found that addition of 3% of cement or 5% of calcium chloride will improve the soil compressibility.
The effect of change of channel width on bed load and transport load of sedimentation for given discharge are studied. The transport load is a mathematical function of change in channel width . The phenomena of transport load of sedimentation in a meandering alluvial channels are significant problems in river engineering and important factor that effects on the works of river control . The finite element model is developed to determine the effect of change of channel width on bed load capacity to ( 2.5 km ) length of the Euphrates river within hit city used value of manning roughness is ( 0.028 ). Calculated the optimum width actualized maximum transport capacity .
To preserve the natural materials, applying the principles of sustainable engineering, to approach the principle of zero waste and to contribute the solution of the negative environmental impact of two decades, which is caused by excessive use of bottles of polyethylene terephthalate (PET) in packaging, has led to the approach of alternative, clean and innovative technologies aimed at recycling and reuse to address this environmental problem. Proposed re-use empty bottles as a way to get rid of them and benefit from them at the same time the way, this method through which the empty bottles cutting into fibres using these fibres made of PET to improve the properties of concrete. Percentage of fiber that has been used are 1%, 1.5%, 2%, 3%, 4%, and 5%. Suitable tests were performed to measure properties of concrete reinforcement by recycle PET fibre such as compressive strength, splitting tensile strength, four-point bending strength, modulus of elasticity and toughness index. Flexural toughness tests were performed to measure the ductility capacities of reinforced concrete members with recycled PET fibre reinforced concrete. The results obtained indicate Toughness index was enhanced by using PET fibre reinforced concrete specimens, compared to no ductility performance of concrete specimens without fibre reinforcement. A significant change in ductility was when observed PET used fibre with 3%.
This paper attempts to obtain bending solutions to plates under uniformly distributed and hydrostatic load distributions using Ritz variational methods and basis functions that are found by superposing trigonometric series and third degree polynomials. Two cases of boundary conditions were considered. In one case, three edges were simply supported and the fourth edge was clamped (SSCS thin plate). In the second case, the adjacent edges were clamped and the other edges were simply supported (SCCS thin plate). This work presents first principles, rigorous derivation of the governing Ritz variational functional and the displacement basis functions for the boundary conditions investigated. The solution is presented in analytical form. The obtained results are compared with previous results obtained using Levy series and Ritz methods and found to be in close agreement . The disadvantage of the method is the associated computational rigour, but the benefit is the accuracy of the results. Comparisons of the present results for center deflections and center bending moments with results in the literature show that there is negligible difference. Double series expressions were found for deflections and bending moments for the plate bending problems solved. Evaluation of the double series expressions at the plate center gave center deflection results that differed from the exact solutions by for to for for uniformly loaded thin plates with three simply supported edges and one clamped edge (SSSC). The differences in the center bending moments Mxx were found to vary from for to for In general, the present results yielded reasonably accurate solutions for the plate bending problems studied.
This study investigates the strength performance and microstructural changes of a sandy gypseous soil improved with fly ash-based geopolymer, for shallow and deep applications. Different proportions of geopolymer were added to a natural gypseous soil having a gypsum content of 30% to 40% with different water contents. The fly ash was activated using sodium hydroxide with molar concentrations 8 and 12 molar and sodium silicate. The ratios of the fly ash to the activator were 1 and 2. Specimens were cured for different ages at 30°C. To simulate the field conditions, a number of specimens were immersed in a salt-saturated solution. Materials performance was evaluated at the macro level by performing unconfined compression test and at micro level by performing scanning electron microscopy test. The study showed that an increase in the molar concentration of sodium hydroxide and of the binder ratio improved material’s strength particularly at lower water contents of the soil. Increasing the binder content to about 30% improved the strength by enhancing the bonding between the soil particles. On the other hand, immersing the samples in the salt solution led, in most cases, to breakdown of the geopolymer network, as confirmed by the SEM images. It was concluded that the fly ash geopolymer-soil mixtures under investigation can provide as high as 8 MPa uniaxial strength under no sulfate attack. However, under sulfate attack condition, this strength can decrease to as low as 0.5 MPa. Even under the worst case, the later strength can be just enough to support shallow foundations rested on a saturated gypseous soil.
AbstractThere is no doubt that the type and properties of cement extremely affect the general properties of produced concrete .Cement is one of the main ingredients of cement past phase in concrete. In present study chemical and physical properties of four types of Portland cement available in Iraqi local market were studied ,these types as follow : two types of ordinary Portland cement Kubaisa (Iraqi cement) and Ismnta (Jordanian cement) and the others of sulfate resisting cement Torab alsabia (Lebanese cement ) and Al-qaim (Iraqi cement).Chemical analysis of the four types of cement were conducted in Baghdad central laboratory in National Center for Constructional Laboratories and Researches (NCCLR) and Al-qaim factory laboratory .The physical tests were conducted in the concrete laboratory of Al_anbar university-college of engineering including standard cement paste ,initial and final setting and compressive strength of cement mortars.The results indicate that the local cement (Kubaisa and Al-qaim) showed better performance than imported cement (Ismnta and Torab alsabia) in most tested chemical and physical properties .Kubaisa cement showed 34.1 % , 35.5 % higher compressive strength compared with Ismnta cement at 3 and 7 day respectively and lower loss on ignition and insoluble residue . The major compounds of Kubaisa cement were nearest to those in typical cement. For sulfate resisting cement , Al-qaim cement showed 13.3 % higher compressive strength at 7 day and lower percentage of C3A (1.95%) . Torab alsabia cement exceed the limits of Iraqi standard I.O.S No.5 1984.
This research aims to propose a new methodology of obtaining the basic solution of the transportation model, which is one of the operations research. Transportation model aimed to find the economic solution to the plan of allocation of products from production centers to consumption centers. One of the important issues of application the transportation model is the issue of transfer raw materials for construction projects (such as ready-mix concrete) and for which there is usually a set of options for production centers as there is always a group of consumption centers (construction sites). This application was chosen because of the wide use of it and due to its impacts on macroeconomic level. Started by reviewing the current methods of obtaining the basic solution of the transportation model, then the factors that are not taken into account in these methods have been identified and, accordingly, two methods have been developed to obtain the basic solution of the transportation model. The first method depends on the indicator of the biggest costs of transport between the centers, while the second method uses the cost multiplied by the amount transmitted (actual cost) as an indicator to determine the basic solution of the transportation model. Unlike other methods, this method considers all variables mentioned in the objective function. Finally, the proposal method has been illustrated by the use of an empirical example.
The buckling analysis of Euler-Bernoulli beam resting on two-parameter elastic foundation (EBBo2PEF) has important applications in the analysis and design of foundation structures, buried gas pipeline systems and other soil-structure interaction systems under compressive loads. This study investigates the buckling analysis of EBBo2PEFs. The governing differential equation of elastic stability (GDiES) is derived in this work using first principles equilibrium method. In general, the GDiES is an inhomogeneous equation with variable parameters for non-prismatic beams under distributed transverse loadings. However, when transverse loads are absent and the beam is prismatic the GDiES becomes a fourth order ordinary differential constant parameter homogeneous equation. General solution to GDiES is obtained in this work using the classical trial exponential function method of solving equations. Two cases of end supports were considered: simply supported ends and clamped ends. Boundary conditions (BCs) were used to obtain the characteristic buckling equations whose eigenvalues were used to determine the critical buckling loads for two cases of BCs considered. It was found that the method gave exact solutions for each of the BCs. The critical elastic buckling load coefficients for dimensionless beam-foundation parameter and ranging from for simply supported EBBo2PEFs were identical with previous results that used Stodola-Vianello iteration methods and finite element method. Similarly, the critical buckling load coefficients for and are identical with previous results that used Ritz variational method.
In the civil engineering, the prediction of cracks for tunnel lining is too hard because it depends by different factors for example concrete strength, tunnel operation conditions, stress and geological surroundings. The aim of this study is to design a Fuzzy inspect System (FIS) for evaluating the concrete cracks of tunnel lining. Fuzzy logic is a method to signify a type of uncertainty which is understandable for user. The system has been designed to meet permit crack formula that issued in “Highway Tunnel Design Specifications”. When the maximal permit crack width as example is chosen as 0.7mm, 1.2mm and 3.3mm separately the fuzziness set accordingly is Minor , moderate and severe. The average error for the predicted crack (element sample) in FIS is 8.34%. The fuzzy evaluation model is based on the information of a real in-service PESHRAW highway tunnel, which reflects field status. Therefore, this evaluation is comfortable.
Abstract The rapid development in computer technology helped to overcome the problem of accuracy improvement and accuracy assessment of high precision network. In this paper a study was conducted to evaluate and compare the accuracy of position through the area of error ellipses in case of using single base line and two base lines for geodetic monitoring network of Haditha Dam . The present paper purpose is to conclude that the use of additional baseline is an important part in the improvement of micronetwork accuracy and treats the weakness in the geometrical figures used.
Despite the importance of plates in structural analysis the flexural analysis of plates under parabolic load has not been extensively studied. This paper presents single finite sine transform method for exact bending solutions of simply supported Kirchhoff plate under parabolic load. The governing equation of equilibrium is a fourth order non-homogeneous differential equation in terms of the deflection The considered thin plate problem has Dirichlet boundary conditions at all the edges. This recommends the use of the finite sine integral transform method whose sinusoidal kernel function satisfies the boundary conditions. The sinusoidal function of x used for the sine transform kernel in this paper satisfies the Dirichlet boundary conditions along edges. The transformation simplifies the problem from a partial differential equation (PDE) to an ordinary differential equation (ODE) in the transformed space. The general solution, obtained using methods for solving ODEs is found in terms of unknown constants of integration which are found by using the finite sine transform of Dirichlet boundary conditions along the and edges. The solution in the physical domain space variables is then found by inversion as a rapidly convergent single series with infinite terms. A one term truncation of the single infinite series yields center deflection solution that is only 2% greater than the exact solution. A three term truncation of the infinite series for gave exact center deflections. Bending moments are found using the bending moment deflection relations as convergent single series with infinite terms.
A voided slab is an innovative type of reinforced concrete slab system developed recently, that has proven its excellence in terms of its structural, environmental, and economic benefits. The self-weight of a slab can be considerably reduced using different shapes of void formers like spherical, cubical, and donut. All researchers confirm that the self-weight of the slab decreases by up to 40%. Various researchers have carried out experimental and numerical studies for studying one-way flexural strength and punching shear strength of voided reinforced concrete slabs. However, the one-way or two-way flexural strength of the voided slab still needs to be acutely investigated. This paper deals with the survey on many titles of selected high impacted journals to illustrated almost criteria of investigations of these types of slabs. The main outcomes of this paper are the term environmental protection, sustainable and plastic waste reduction had a role not a little in this research, as 16% of the research on this topic were studied. Also, the plastic material governs the subject of the raw materials used to make the voids;43% of researches used this material.
Processed and natural clays are widely used to construct impermeable liners in solid waste disposal landfills. The engineering properties of clay liners can be significantly affected by the leachate from the waste mass. In this study, the effect of inorganic salt solutions on consistency and compressibility characteristics of compacted clay was investigated at different concentrations. Two type of inorganic salt MnSO4 and FeCl3 are used at different concentration 2%, 5%, and 10%. The Clay used was the CL- clay (kaolinite). The result shows that the consistency limits increased as the concentration of salts increased, while the compression index (Cc) decreases as the concentration increased from 2% to 5%, after that the Cc is nearly constant. The swelling index (Ce) tends to increase slightly as the concentration of MnSO4 increased, while it decreases as the concentration of FeCl3 increased.
The analysis of the least compressive load that cause buckling failures of Euler-Bernoulli beams resting on two-parameter elastic foundations (EBBo2PFs) is vital for safety. This article presents Ritz variational method (RVM) for the stability solutions of EBBo2PFs under in-plane compressive loads. The Ritz total potential energy functional, was derived for the problem as the sum of the strain energies of the thin beam, the two-parameter lumped parameter elastic foundation (LPEF) and the work potential due to the in-plane compressive load. Ritz functional was found to depend upon the buckling function w(x) and its derivatives with respect to the longitudinal coordinate. The principle of minimization of was implemented for each considered boundary condition to find the w(x) corresponding to minimum Three cases of boundary conditions investigated were: clamped at both ends, clamped at one end and free at the other, simply supported at both ends. For each case, w(x) was found in terms of unknown generalized buckling parameters ci, and buckling shape functions satisfying the boundary conditions. Thus was expressed in terms of the parameters ci. The Ritz functional was subsequently minimized with respect to the parameters yielding an algebraic eigenvalue problem. The condition for nontrivial solutions of homogeneous algebraic equations was used to find the characteristic buckling equations that were solved to find the eigenvalues. The eigenvalues were used to find the buckling loads and the critical buckling load. It was found that a one-parameter RVM solution for the EBBo2PF with both ends clamped, and with one clamped and one free end gave similar critical buckling load solutions to those presented in the literature. It was also found that an n-parameter RVM solution for the EBBo2PFs with both ends simply supported yielded exact buckling load solutions because exact sinusoidal buckling shape functions were used.
Abstract The rapid development in computer technology helped to overcome the problem of accuracy improvement and accuracy assessment of high precision network. In this paper a study was conducted to evaluate and compare the accuracy of position through the area of error ellipses in case of using single base line and two base lines for geodetic monitoring network of Haditha Dam . The present paper purpose is to conclude that the use of additional baseline is an important part in the improvement of micronetwork accuracy and treats the weakness in the geometrical figures used.
Construction delays are common problems in civil engineering projects in Arab countries. Because of the importance of this problem, the study reviewed many studies that dealt with the topic of delay in the construction projects of their countries.The study included the delay in projects in Iraq. Jorden, Palestine, Saudi Arabia, United Arab Emirates, Qatar, Yemen, Egypt, Sudan, Algeria and Morocco. The projects included infrastructure facilities, public buildings, housing complexes, water treatment plants, sports facilities, water supply, roads. Quantitative method via a structured questionnaire was implemented in all these studies, the questionnaires were distributed to experienced project parties such as the owner, contractor, consultant and other parties. The relative importance method was used to analyze the results of the questionnaire to obtain the highest ten or five factors with the highest rank which cause delay. The results showed that the groups of contractor and owner has the highest percentage and were repeated several times compared to the rest of the groups.The top five factors causing delay of construction projects in Arab countries are, problems of cash flow and financial by owner, difficulties in financing the project by the contractor, Poor site management and supervision of the contractor, selecting the contractor who has the lowest bid and ineffective planning and scheduling by contractors
The Light Falling Weight Deflectometer (LFWD) was developed to estimate the in-situ elastic modulus directly to the layers near the base as subgrade and subbase layers. The field tests were carried out on selected sections from landfill project within Anbar Province. Furthermore, Forty test sections have been constructed and tested at the Civil Engineering Department- University of Anbar. All sections were tested using the ZFG 3000 model - LFWD in companion with the Plate Load Test (PLT) which were used as reference measures. Regression analyzes were performed to determine the best correlation between the elastic modulus obtained from LFWD and PLT tests. ANN model was used to calculate Evd and compare the regression statistical model. It was found that the ANN model showed a higher performance than regression analysis in predicting Evd. Satisfactory correlations were obtained, which showed that LFWD could be a promising device for in-situ characterizing of subsurface and subgrade layers.
Land cover assessment is a significant research area in GIS and remote sensing, aiding decision-makers in understanding land use changes' underlying forces and enabling effective actions. In general, Iraqi cities are experiencing severe degradation of agricultural lands due to population growth and residential development, impacting socio-economic and environmental quality. In addition, the deriving forces of transforming the lands from agricultural to other land cover types are not well understood. Research is needed to map and assess agricultural lands for better economic and environmental solutions. The study uses ANN-CA integration to predict agricultural land changes in Babil province, central Iraq. The CNN model achieved the highest accuracy, with a total land cover transformation of 2143.1 square kilometres between 2000 and 2020. the overall accuracy was 0.95, 0.93, and 0.90 based on images captured in 2020, 2000, 2010) respectively. This methodology is considered an efficient tool for monitoring agricultural lands and developing development plans in Iraq.
Corrosion in steel bars is considered a big problem because corrosion is mainly responsible of decrease virtual age of structures and many risks indicated by deterioration. In addition, corrosion increases the cost of maintenance, particularly structures exposed to harsh environmental condition. FRP bars (Fiber Reinforced Polymer) became an alternative material from traditional steel bars. FRP had properties made it used in civil engineering sectors which are lightweight, non-corrosive, non-conductive made it a preferred alternative from steel bars in aggressive environments. FRP bars don’t have yield made it con not bind outside its linear behavior to make ties, because of the brittle behavior of FRP bars up to failure. So that, the new innovative manner by using CFRP sheets stirrups immerged by sikadur330 for produce beams can resist the harsh condition and purely reinforced with FRP in a new manner can provide stirrups in full different sizes and with lower cost. Twelve beams reinforced with GFRP bars in three different ratios of tension reinforcement (four beams for each ratio). Three control beams with steel stirrups: two beams were designed to fail in shear. Whilst, the residual nine beams with shear reinforcement made from CFRP sheets strips, immerged by sikadur330. The main variable were studied is the change in type and amount of secondary reinforcement and change in amount of primary reinforcement. The test was conduct under four point loading and in simply supported conditions. The result of tested beams illustrated that, beams had a higher percentage of tension reinforcement and shear reinforcement displayed an increasing in ultimate load about 38.1% from related control beam. While, an equivalent amount of shear reinforcement displayed an increasing in carrying load capacity up to 10%. In maximum ratio of CFRP sheets immerged by sikadur330 stirrups convert failure mode from shear to flexural indicated by crushing in cover of concrete. In addition, increased energy absorption, changed cracks orientation, increased energy absorption, decrease principal strain and increased concrete tensile.
In this paper, a practical method of analysis of the pile displacements is proposed on the basis of the theory of load-transfer curves widely used in pile design and analysis. The parameters of the load-transfer curves for piles under axial load (called t-z, q-z curves) or lateral load (called P-Y curves) were correlated with the number of blows Nspt measured during the standard penetration test (SPT). Well documented case histories of full-scale axial or lateral loading tests on single piles in sand were collected, and the analysis of the experimental results led to define the parameters of the load-transfer curves. Two practical methods of computation of a single pile under an axial load or a lateral load were proposed to be used within the scope of a pile foundation project. At last, a validation process of the load-transfer curves was undertaken by direct comparison of the predicted pile displacements to those measured during other pile loading tests, which showed a good predictive capability of the two proposed methods